LUp to 3 menu items can be displayed at a time. When the batteries are fully charged, 5 remains on the display. LIt takes 7 hours to fully charge the batteries, however, you can use the handset before the batteries are fully charged.
LClean the charge contacts page 8 of the handset and base unit with a soft, dry cloth once a month, otherwise the batteries may not charge properly. Clean more often if the unit is exposed to grease, dust or high humidity. LWhen 7 flashes, recharge the handset batteries. LIf the handset is turned off, it will be turned on automatically when it is placed on the base unit.
After your Panasonic batteries are fully charged, you can expect the following performance:. LActual battery performance depends on a combination of how often the handset is in use talking and how often it is not in use standby. LBattery operating time may be shortened over time depending on usage conditions and ambient temperature. If 7 flashes even after the handset batteries have been charged for 7 hours, the batteries must be replaced. LWe recommend the use of Panasonic rechargeable batteries noted on page 6.
If you install non-rechargeable batteries and start charging, the batteries may leak electrolyte. See page 10 for battery installation. LThe date and time may be incorrect after a power failure. In this case, set the date and time again. The handset features a digital speakerphone, which allows you to have hands-free conversations. The unit will redial up to 11 times. While the handset is redialling, mute is automatically turned on. LPlace the cursor to the right of where you want to insert a number, then press the appropriate dial key.
You can change the tone quality of the receiver while you are on a call. You can mute your voice during a conversation. While mute is turned on, you will be able to hear the other party, but the other party will not be able to hear you. The handset can be locked so that no calls or settings can be made. Incoming calls can be answered, but all other functions are disabled while key lock is on. LCalls to emergency numbers page 31 cannot be made until key lock is turned off.
Contact your service provider for details. Consult your PBX dealer for details. A pause is sometimes required when making calls using a PBX or long distance service.
To change pause length, see page You can temporarily switch the dialling mode to tone when you need to access touch tone services e. LYou can change the dialling mode depending on your telephone line service page LBefore recording a conversation, you should inform the other party that the conversation will be recorded.
Erase unnecessary messages page LWhile recording a conversation, you cannot change the tone quality of the handset. Any key answer feature. You can answer calls simply by lifting the handset off the base unit.
You do not need to. Place the cursor to the right of. LOnly the one touch dial assignment is erased. The corresponding handset phonebook entry is not erased. This feature allows you to dial phone numbers in the handset phonebook while you are on a call. This feature can be used, for example, to dial a calling card access number or bank account PIN that you have stored in the handset phonebook, without having to dial manually. The shared phonebook allows you to make calls without having to dial manually.
Any handset registered to the same base unit can use the shared phonebook. You can add 20 names and phone numbers to the shared phonebook and search for shared phonebook entries by name. Repeat step 6. Erase unnecessary entries page Place the cursor to the right of where you want to insert a number or character, then press the appropriate dial key.
Shared phonebook entries can be searched for by first character or by scrolling through all shared phonebook entries. Note: L Voice memos are treated as new messages. Memory capacity The total recording capacity including your greeting message, caller messages, voice memos, audible call announcements, and recorded conversations is about 15 minutes.
A maximum of 64 messages can be recorded. Erase unnecessary messages page Using the answering system remotely 1 Dial your phone number from a touch tone phone. Note: Turning on the answering system L If less than 5 minutes of recording time is available, the unit will announce the remotely remaining recording time after the last If the answering system is off, you can turn it message is played back.
L If message memory is full, erase 1 Dial your phone number from a touch unnecessary messages page L A long beep will be heard. It is necessary to check Message alert Off page the number of rings required to activate 51 the voice mail service provided by your service provider before changing this Changing the number of rings setting.
You can change the number of times the phone rings before the unit answers calls. If you call your phone from messages. The base unit beeps about once a minute until you have listened to all new messages.
Additional handsets will base unit easy registration give you the freedom to, for example, have The included handset and base unit are an intercom call with another handset while preregistered. After purchasing an a third handset is on an outside call.
See additional handset, register it to the base page 6 for information on ordering additional unit. Ensure that the additional handset is handsets. Additional base units 3 Place the additional handset on the Handsets can be registered to up to 4 base base unit. The registration tone units, allowing you to add additional base continues to sound.
With the handset units and extend the area in which your still on the base unit, wait until a handset s can be used. Start again from handset moves from one radio cell to another. L Charge the batteries of your additional L Intercom calls and call transfers are only possible between handsets in the same handset for about 7 hours before initial radio cell.
L This registration method cannot be used for handsets that have already been registered to a base unit. Register the handset manually manual registration; page L The handset starts searching for the base unit. A handset can cancel its own L This number is used by the handset registration or the registration of another as a reference only. If keytones are turned on cancel, by pressing the desired handset page 29 , a confirmation tone will be number. L The selected handset number s will flash.
The number automatically use any available base unit it will stop flashing. A handset can cancel a base mode on. The L While the repeater mode is turned on, number will stop flashing. Intercom between Note: handsets L To register the handset to another base unit or to the same base unit again, see Intercom calls can be made between manual registration page Please use only number.
L The outside call will be put on hold. L Handset 2 can talk with handset 1. L The other handset rings if it is within range of the base unit and turned on. L The outside call rings at the other handset. Note: L k flashes to indicate the outside call is on hold.
L If the other handset user does not answer the call within 1 minute, the call will ring at your handset again. L Do not pinch the telephone line cord and AC adaptor cord between the base unit and the wall.
L Use the following wall template to position the screws before drilling. L The handset is not registered to the base unit. Register it page L The handset is too far from the base unit. Move closer. L The AC adaptor is not connected. Check the connections. The handset display is blank. L The handset is not turned on.
Turn the power on page The handset will not turn on. L Make sure that the batteries are installed correctly page L Fully charge the batteries page L Clean the charge contact and charge again page L The AC adaptor or telephone line cord is not connected.
L If you are using a splitter to connect the unit, remove the splitter and connect the unit to the wall socket directly. If the unit operates properly, check the splitter. L Disconnect the base unit from the telephone line and connect the line to a known working telephone. If the working telephone operates properly, contact our service personnel to have the unit repaired. If the working telephone does not operate properly, contact your service provider. L The call bar feature is turned on.
Turn it off page L You dialled a call restricted number page L The key lock feature is turned on. The unit does not ring. L The ringer volume is turned off. Adjust the handset ringer volume page 25 and the base unit ringer volume page L The night mode feature is turned on.
Turn it off page 26, The batteries should be charging L Clean the charge contact and charge again page but the battery icon does not L The AC adaptor is disconnected. Plug in the AC adaptor. Move pressed. L Another handset is on an outside call. Wait for the other user to complete the call. Static is heard, sound cuts in and L Locate the handset and the base unit away from out.
Interference from other other electrical appliances. L Move closer to the base unit. L Your unit is connected to a telephone line with DSL service. Get the Manual Here. I noticed the original batteries are marked mAh. Does this mean the standard rechargeable is not sufficent?
Was this answer helpful? Yes No. Allan posted an answer 12 years, 9 months ago. As I still have the original manual, I thought I would just check the web site to see if it was the same and found it was. Hope this is of help to you. Select colour Sorry, this product is currently unavailable at any of our online retailers.
Compact Design The phone is compact enough to fit in narrow space. Speakerphone Do something else while talking You can talk with your hands free.
See All Specs. Get Inspired. Products recently viewed Products recently viewed. Visit the support page.
0コメント