The Kyocera manuals for Printer are available online for free. You can easily download all the documents as PDF. E-mail address. Remember login. Login or create new account. Add to Favourites.
Download as PDF. Overview View all the pages Comments. Page Adjust the Finisher Tray Extension to accommodate the size of paper. Shake the toner container approximately 10 times in the horizontal direction to stir toner. Turn the toner container release lever and gently push the toner container into the MFP. Connect the connector of the drawer heater. Connect the power cord. Connect the power cord to the connector on the MFP.
Insert the power plug into the wall outlet and turn the power switch on. Installing the toner maintenance item U Press the start key to execute the maintenance item. Installation of toner starts and time minutes is indicated until the installation ends.
Load paper. Output an own-status report maintenance item U Make test copies. Place an original and make test copies. End of installation. Place the MFP on the paper feeder by aligning the positioning insertion sections of the MFP with the positioning pins at the rear part of the paper feeder.
Stack a paper feeder on another paper feeder by aligning the positioning insertion sections of the first paper feeder with the positioning pins at the rear part of the second paper feeder. If a type of paper that is not included in the specifications for the standard sheet cassette size is used, replace the cassette size sheet indication with the supplied one.
Insert the MFP power plug into the wall outlet and turn the power switch on. Positioning pins. Press the Interrupt key to output the test pattern and check the image. If an adequate image cannot be obtained, carry out the following adjustment. If a test pattern a is obtained, increase the adjustment value.
If a test pattern b is obtained, decrease the adjustment value. Setting range: Output the test pattern again. Repeat steps 2 and 3 until an adequate image is obtained. Close the DP, fit the fixing fitting from the rear side of the right hinge, and secure it with the two bronze TP screws M3 x Clean the pasting position for the caution label with alcohol.
Paste the caution label that corresponds to the language according to the destination to the DP. Prepare an original on which 4 lines are drawn 15 mm from the edges and the center line is drawn. Set the original on the DP and make a test copy to check the copy image.
At this time, set the paper guide for the original table and drawer to the paper size to be used. If the copy image does not match the original image, carry out the following adjustments in maintenance mode. Run maintenance mode Set originals in the original tray and press the interrupt key.
Make a test copy to check the image. For copy example a: decrease the value. For copy example b: increase the value. A smaller setting value makes the copy image shorter. A larger value makes the image longer. Select LEAD1. For copy example a: increase the value. For copy example b: decrease the value. Changing the value by one moves the leading edge by 0.
The larger the value, the later the image scan start timing. Select 1sided. For adjustment of the front side in duplex copying, select 2sided front. For adjustment of the back side, select 2sided back. Set originals in the original tray and press the Interrupt key. The larger the value, the center of the image moves toward the right. The smaller the value, the center of the image moves toward the left.
Remove the stop ring and the strap from the rear side. Restore the conveyor section. Remove the fitting projection and pin, and then remove the stopper from the front side.
Open the left cover until it is put horizontally. Turn the wire guide section of the duplex unit in the direction indicated by the arrow. Insert the axis sections of the duplex unit into the U- shape grooves of the conveyer unit. Press the duplex unit in the direction indicated by the arrow to fit the claws into the conveyer unit. Hang the hook of the plate lock on the conveying unit and then turn the plate lock to fit the hole to the claw of the duplex unit.
Secure the duplex unit with the two S tite screws M3. Open the conveyer unit and connect the connector of the duplex unit to the MFP. Reattach the removed parts to their original positions. Connect the MFP power plug to the wall outlet and turn the power switch on. Press the Interrupt key to output the test pattern in the duplex mode and check the image. Remove the main body from the paper feeder see page Remove the right cover. Pull out the drawer. Remove the three screws and then the front right cover.
Insert the cassette heater from the bottom of the machine and attach it to the MFP. Remove the two screws and open the power source PCB in the direction indicated by the arrow. Fit the wire of the drawer heater into the groove of the frame and put it inside the power source PCB. Refit all the removed parts. Fit the key counter socket assembly to the key counter retainer using the two screws and nut.
Fit the key counter mount to the key counter cover using the two screws, and attach the key counter retainer to the mount using the two screws. C Key counter cover. Cut out the aperture plate on the right cover using nippers. Connect the 4-pin connector of the key counter wire located at a longer distance from the tube to YC13 on the engine PCB, pass the wire through the two clamps, and pull the other 4-pin connector out from.
Fold the 7-pin connector of the key counter wire back, pass the wire through the clamp at the upper part of the controller box, and hang it. Connect the 4-pin connector of the key counter to the key counter wire. Engage the projection of the key counter mounting plate with the aperture of the right cover. Secure the key counter cover and the key counter mounting plate together with the MFP using a M4 x 35 screw. Insert the key counter into the key counter socket assembly. Turn the power switch on and enter the maintenance mode.
Exit the maintenance mode. Check that the message requesting the key counter to be inserted is displayed on the message display when the key counter is pulled out. Check that the counter counts up as copies are made. When placing the transfer unit on the floor or the like, be sure to place it upside down.
If not, the staple mounting plate may be deformed, resulting in a malfunction. Be sure to remove the tape for the intermediate tray at Procedure 16 not removing before mounting. Remove the two screws to remove the upper left cover. Release the fitting parts using a small screw driver or the like and remove the front side cover. Remove the screw and the fitting part located on the right side and then remove the left front cover.
Insert the transfer unit from the MFP front side and slide it to the left to install to the ejection part. Loosen the screw located at the rear side of the transfer unit and release the lever securing fitting in the direction of an arrow, and then retighten the screw.
Loosen the screw located inside of the MFP by about 3 turns. Hang the hook of the hook holder onto the screw and then retighten the screw. Insert the intermediate tray from the front side of the MFP while pushing the hook to the back and then push the pin located at the right rear side of the intermediate tray into the hook holder until the fitting sound is heard. Hook holder. Fit the pin located at the left rear side of the intermediate tray from the rear side of the MFP onto the hook of the transfer unit.
Remove the tape and pull out the pin connector and pin connector. Connect the pin connector of the intermediate tray to the connector of the transfer unit. Connect the pin connector of the intermediate tray to YC5 on the engine circuit board. Attach the cover that has been removed by Procedure 8 to its original position using the two screws.
Attach the large ejection cover with the two screws that have been removed by Procedure 1. Attach the inner cover that has been removed by Procedure 3 to its original position. Insert the front and rear hooks of the copy tray into the front ejection cover and rear ejection cover each and then attach the copy tray. Open the staple cover and then insert the staple cartridge into the staple unit.
Insert the MFP power plug into an outlet and then turn the power switch on. Select the staple mode and check the staple operation. Welcome to ManualMachine. We have sent a verification link to to complete your registration.
Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Kyocera KM Service manual Download for 1. Published in October FT Revision 1. Revision history Revision Date Replaced pages Remarks 1 15 October , 2, 3, , 2, 4, 5, , 3, 4, 12, 14, 20, - 22, 23, 27, 28, 29, 30, 32, 34, 38, 44, 53, 54, , , 19, 20, 21, 22, 23, 24, 25, , 19, 21, 35, 36, 38, , 8, 9, Desktop Copying system Indirect electrostatic system Originals Fixed Copy paper First copy time Single positive corona charging Recording system Semiconductor laser Developing system Single component developing system Toner: magnetism toner Toner replenishing: automatic from a toner container Transfer system Transfer roller Separation system Curvature separation and separation electrode Fixing system Exposure by cleaning lamp Cleaning system Cleaning blade Scanning system Flat bed scanning by CCD image sensor Bitmap memory Inert gas lamp Dimensions Automatic paper selection, Image quality selection, Automatic sizing selection function, zoom function, Duplex copy, Divided copy, Binding margin, Border width, Aggregate copy, Sort copy, Eco-copy, Copy program and Section management mode Power source Same as copying speed First print time Internal type Copy paper Electrically connected to the MFP Dimensions Avoid direct light and high humidity.
Exit maintenance mode. Remove the two pins for light source unit. Pins Figure Install the optional duplex unit as necessary see pages to Quick Links. Table of Contents. Scan System F. Previous Page. Next Page. Kyocera KM Service Manual pages. Kyocera Ci Technical Reference Manual pages. Kyocera network printer advanced operation guide km, km, km pages. Hewlett-packard user guide printer kyocera extended driver pages.
Kyocera operation guide copier and printer km, km, km pages. Supported models: fs, fs, fsmfp, fsd, fsd, fsdn, fsdn, fsdn, fsdn, fsdn, fs-cn, fs-cn, fs-cn, fs-cn, fs-cdn, km, km, km, km, km, km, km, km, km pages. Page 2 This Operation Guide mentions that is a 16 ppm prints per minute machine, is a 20 ppm prints per minute machine and is a 25 ppm prints per minute machine. Note This Operation Guide contains information that corresponds to using both the inch and metric versions of this machine.
It explains set-up procedures and other related operation on the machine. As the required set-up in order to use the copier as a scanner may differ depending upon the environment in use in the connected computer, please read those sections related to your specific computer environment and perform the appropriate set-up procedures explained there.
Page 5 Important: The use of scanned legally copyrighted materials, such as documents, musical scores, pictures, woodblock prints, maps, drawings and photographs, for any intent other than your own personal or home use, or other such purpose, is prohibited under the copyright law without prior permission from the legal copyright owner.
Page 6: Getting Connected Getting connected The following procedures are required in order to use this machine as a scanner. Page 9: Preparations Preparations Names of parts Main body Original cover — Open and close this cover when setting an original on the platen. Platen — Set the original to be scanned face-down in the left-rear portion of the platen.
Original size indicator lines — Be sure to align the original with these lines when setting an original on the platen. Message display — Indicates the scanner condition or setting values.
0コメント