Use your best discretion but it may be best to stay on the safe side to avoid headaches in the future. Brionna is on a roller coaster that only goes up. You can follow her on twitter BrionnaLewis. The degree to which a driver can legally tint their car's windows vary from state to state. Terminology These are the terms you need to know in order to interpret the various state laws and limits.
You're going to need almost a gallon of soapy water throughout this process. Prepare the water ahead of time to make working easier. A spray bottle is highly recommended. Take a clean rag and dry the window. Wipe away the soapy water on both sides and dry off the edges as well. If you're using a spray bottle, refill it with more soapy water.
A squeegee will help you get the window completely dry. Make sure you get underneath the seals in the interior of the car. Use your finger to get under the seal and remove dirt and dust. Roll the window back up before beginning, but leave your car on. You'll need to move the window up and down as you work.
For now, leave it up. Determine which side of the tint is adhesive. Like a sticker, the tint has a layer that can be peeled off right before adhering it to the window. Make sure, as you work with the tint, that this side is facing you.
Part 2. Spray the outside of the window with soapy water. The water will help the tinting temporarily adhere, but still make it slippery enough to slide around and put into place. Place the tinting over the outside of the window so that it covers the entire window.
Unroll your tinting so that it covers the entire window, with at least " of extra tinting over the edges. The liner the part that will later adhere to the window , should be facing you.
Make sure you do not remove the liner -- you're just sizing and pressing the tinting right now, now adhering it. Cut away a manageable slab of tinting. You should have a few inches of extra tint in every direction, but you don't want to be maneuvering the entire roll of film while working. Use a precision knife or blade to cut a usable square of tinting film from the larger role. Spray the front of the film with water. Once the tint is cut into a square, it should stick to the water on the outside of the window.
You should then spray the tint itself so that the entire thing is covered in a thin layer of soapy water. Take your knife and cut along the bottom and left edges of the window. Simply use the edges of the window to trace your knife across the tinting film. You want a perfectly shaped line to ensure the tint fits. When done, two of the edges should fit perfectly, and the rest should still be square. As you cut, use the squeegee or your free hand to make sure the film is flush with the window.
When done, cut the excess film away and discard. Pull the film 1" towards the left edge. You want to shift the film towards the edge you just cut. This ensures that you have enough tint to cover every edge of the window, including the part covered by the seal. Cut the right edge, then slide the tint halfway back towards the center. Pull the film down roughly one inch, so the bottom edge is lower than the window.
This is the tint that will eventually go into the door, allowing you a better light seal. Slide it down and then use the squeegee to flatten it again. You'll be doing the same thing you just did with the right and left side on the top and bottom edges.
Lower the window a half inch, then use the top of the window to cut the film to shape. Once the window is lowered, you can use this top edge of the window as your guide. Use the precision knife to cut right to the top of the window. When done, pull the tint back towards the center.
Clean up any of the corners that have excess film. When cutting away, the corners may have bits and pieces of extra film in the corners. Use your knife to clean it all up. Realign your film so that it fits the window perfectly, with some excess on every edge.
You may need to reapply water to make it stick. If so, remove the cut tint, spray some more soapy water, and reapply the film to the window. Working from the top down, use a heat gun and a hard card to push the bubbles to the bottom. Get out all the air and water by working from the top downward. Smooth the entire film out on the outside of the window. As you push to the bottom, you'll see zig-zagging from the "fingers" of air still stuck in the film.
This is a good sign. Keep pushing downward, then run the heat gun along the bottom of the window to make sure it is all dried out. You'll have to prep the inside window a bit more, so this is a good place to ensure that the tint stays dust free.
Part 3. Prep the inside of the window with soapy water and a squeegee. You're going to go through a lot of soapy water in this process.
You can use a hard edge to get in between the seal and the window for a better clean. When done, spray the whole window with soapy water. Peel off the top half of the release liner from the tinting film. Window tint works just like a sticker. There is a removable layer that adheres to the tint and keeps the adhesive solid. You should, however, only peel off only the top half for now-- it makes it easier to work with. Spray off the now-exposed section with fresh water.
You are now ready to adhere the tint to the window. Eventually, any quality tinted window film installed by Car Audio City will prove durable and cleanly applied. However, the window tint will be vulnerable while its adhesives dry, so even little, honest mistakes can damage an otherwise perfect application.
Leave them rolled up at least two to four days. Everybody who lived through the s knows about the dreaded air bubbles that can become trapped in cheap window film, ruining a window tint forever. However, window tint bubbles you notice after an install are much more likely to be caused by moisture, and should evaporate within a few days, as the tint cures.
As for how long bubbles stay in window tint, times will vary depending on climate, but give it four days at least. It takes a little patience, but the bottom line is you want to do everything you can to let tinted window film dry before doing anything that could damage it.
San Diego sunshine can help, and in general window tint cure times are shorter in summer, meaning two to four days. However, the window tint cure time during winter and rainy months can extend the wait as long as a month. For example, park in direct sunlight on clear days, but if you can, park inside on cool or rainy days, as well as overnight. Once enough time has passed, you may go ahead and proceed with routine use of your car, knowing your tinted window film will remain ins good shape.
We recommend leaving them rolled up anyway, cranking up your car stereo, and going for a ride in your newly tinted automobile. When considering DIY car window tint vs.
0コメント